HINSONMotorsports.com
Dual & Triple Fuel Pump Harness Package with Hobbs Switch
Dual & Triple Fuel Pump Harness Package with Hobbs Switch
Couldn't load pickup availability
Plug-and-play relay harness for HINSON dual and triple fuel pump modules, with pump staging included. Each pump gets its own relay circuit, the harness plugs straight into the fuel hat, and a 4 psi Hobbs pressure switch is in the box so you can cruise on one pump and bring the next on under boost.
Staged pump control, included
Pump one runs full time. Pump two comes on at 4 psi of boost through the included Hobbs switch. That means less fuel heat, less current draw and less pump wear when you're cruising, and full flow when you need it. Running every pump all the time makes the regulator return fuel the engine isn't using, which heats the fuel.
Not boosted, or want a different trigger? Stage with a wide-open-throttle switch, RPM signal, ECU output, nitrous controller or a manual switch instead.
Key features
- Dual or triple. Choose the pump count to match your module. Each pump is its own circuit.
- Relay and fuse per pump, sized for the pumps' current draw, with power and ground straight from the battery.
- Plugs into the fuel hat. Mates directly with the connector on top of every HINSON fuel pump module.
- Three connections at the tank: the factory pump 12V signal (turns the harness on) and the two fuel level sender wires (keeps your gauge working).
Choosing your trigger
- Dual: plug the Hobbs switch into one circuit with the adapter harness and put the circuit loop on the other. Either pump can be the primary.
- Triple: treat circuits two and three separately. A second Hobbs switch at a higher pressure is easier on the electrical system than both pumps kicking on at once, or trigger pump three with WOT, vehicle speed, an RPM window switch or an ECU output.
- Run continuously: install a circuit loop on every circuit and all pumps run whenever the harness is on.
What's included
- Main harness with a relay and fuse per pump (2 or 3)
- Battery power and ground leads
- Fuel hat connector
- 3-pin tank connection (pump 12V signal and fuel level sender pass-through)
- Circuit loop for each pump circuit
- 4 psi Hobbs pressure switch with adapter harness (unless you choose to remove it)
- Printed harness installation guide
Removing the Hobbs switch
You can remove the 4 psi Hobbs switch and save $20 if you plan to stage your pumps another way. Most customers keep it: it's the simplest way to stage pumps on a boosted build.
Before you install
This harness is plug and play at the fuel hat. At the tank, you'll connect three wires to your factory wiring. Tank-side wire colors change by model year, so we can't give a reliable color chart for every vehicle; identify the factory pump 12V feed and the two fuel level sender wires on your vehicle before connecting. Professional installation is recommended.
Fits
Every HINSON dual and triple fuel pump module: Pontiac GTO 2004โ2006, Chevrolet Trailblazer SS 2006โ2009, GM trucks and SUVs 1998โ2017, Chevrolet S10 & Blazer 1994โ2004, Chevrolet Camaro & Pontiac Firebird 1998โ2002, Chevrolet Camaro 2010โ2015, Pontiac G8 2008โ2009, Cadillac CTS-V 2004โ2013, Hummer H2 2003โ2009 and Jeep Wrangler JK 2007โ2018. Triple harness: GTO, 2004โ2017 GM trucks and SUVs, and Trailblazer SS.
Install guide
Harness guide ยท All fuel pump support
FAQ
Is the harness required?
No. You can build your own; you'll need a 30-amp relay circuit per pump. Most people can't build one for less than ours.
Which wires do I connect at the tank?
Three: the factory pump 12V feed and the two fuel level sender wires. Identify them on your vehicle before connecting.
Does staging work on a naturally aspirated engine?
Yes, but the Hobbs switch won't trigger under vacuum. Use a wide-open-throttle switch, RPM signal or ECU output instead.
Materials
Materials
Shipping & Returns
Shipping & Returns
Dimensions
Dimensions
Size12x1.25mm
- Product Dimensions โ : โย 4.5 x 0.9 x 4.5 inches
Care Instructions
Care Instructions
Share
